series ame1-az 1watt | ac-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r8.h 1 of 3 north america only features: models single output model input voltage (vac/hz) input voltage (vdc) temperature range (oc) output voltage (v) output current max (ma) maximum capacitive load (f) efficiency (%) 115 vac 230 vac 277 vac 480 vac ame1-3.3saz 90-305/47-440 130-430 -40 to +80 3.3 300 2200 62 59 58 ame1-5saz 90-305/47-440 130-430 -40 to +80 5 200 1100 58 57 56 AME1-12SAZ 90-305/47-440 130-430 -40 to +80 12 83 680 73 68 65 ame1-15saz 90-305/47-440 130-430 -40 to +80 15 67 560 77 68 70 ame1-24saz 90-305/47-440 130-430 -40 to +80 24 42 470 79 79 77 ame1-3.3sbaz 90-528/47-440 130-745 -40 to +80 3.3 300 2200 51 51 50 44 ame1-5sbaz 90-528/47-440 130-745 -40 to +80 5 200 1100 57 57 56 50 ame1-12sbaz 90-528/47-440 130-745 -40 to +80 12 83 680 62 62 60 51 ame1-15sbaz 90-528/47-440 130-745 -40 to +80 15 67 560 61 59 58 50 ame1-24sbaz 90-528/47-440 130-745 -40 to +80 24 42 470 58 58 56 48 input specifications parameters conditions typical maximum units current (full load) 115 vac ? 25 ma 230 vac ? 20 ma 277 vac ? 15 ma 480vac ? 5 ma inrush current <2ms (cold start) 115 vac ? 10 a 230 vac ? 15 a 277 vac ? 20 a 480 vac ? 30 a leakage current ? 0.15 ma external fuse recommended slow blow type 1 a input dissipation (no load) Q 0.3 w output specifications parameters conditions typical maximum units voltage accuracy full load (typical)* 5 % line regulation ll-hl, full load 1.5 % load regulation (single output) 0-100% load (typical)* 5 % transient recovery time 200 s transient response deviation 25% load step 2 % of vout minimum load 0 % ripple & noise 3.3/5 vdc with 560f e/c 200 mv p-p 12/15 vdc with 220f e/c 400 mv p-p 24 vdc with 220f e/c 500 mv p-p *ripple &noise measured at 20mhz bandwidth with 0.1f and 115/230/277/480 vac (typical input) with full load. isolation specifications parameters conditions typical rated units tested i/o voltage 60 sec 3000 vac isolation resistance >1000 m ? ? i/o isolation 3000vac ? ? operating temp: -40 c to +80 c ? input: 90-305vac, 47-440hz, or 130-430 vdc ? optional 90-528vac, 47-440hz, or 130-745 vdc ? ? ultra small package ? over load, short circuit protection click on series name for product info on aimtec.com
series ame1-az 1watt | ac-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r8.h 2 of 3 north america only general specifications parameters conditions typical maximum units switching frequency 100 khz over load protection auto recovery >125% short circuit protection auto recovery operating temperature without derating -40 to +80 o c storage temperature -40 to +85 o c maximum case temperature 100 o c humidity non condensing 20 ~ 95 % rh case material plastic resin + fiberglass (flammability to ul 94v-0) weight 25 g dimensions (l x w x h) 1.40 x 0.92 x 0.76 (35.60 x 23.31 x 19.32mm) mtbf > 400,000 hrs (mil-hdbk -217f, t=+25oc)/full load > 100,000 hrs (mil-hdbk -217f, t= at highest operating temperature)/full load note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. environment approval parameters conditions shock wave form: half sine wave acceleration amplitude: 5gn bump duration: 30 ms number of bumps: 18 (3 in each direction for every axis) converter operation before and after test, body mounted (on chassis) vibrations test mode: sweep sine 10-100hz, speed 0.05hz/s displacement: 1mm acceleration: 3g 3 loops 30min one cycle, 3h total, every axis tested converter operation before and after test, body mounted (on chassis) safety specifications parameters agency approvals culus, ce, cb, fcc standards information technology equipment iec/en/ul 60950-1:2006+a11:2009 emi - conducted and radiated emission en55022, class b (* see note) harmonic current emissions iec/en 61000-3-2, class a voltage fluctuations and flicker iec/en 61000-3-3, (en60555-3) electrostatic discharge immunity iec 61000-4-2 rf, electromagnetic fiel d immunity iec 61000-4-3 electrical fast transient/burst immunity iec 61000-4-4 surge immunity(1kv) iec 61000-4- 5(saz:level2,sbaz:level 1) rf, conducted disturbance immunity iec 61000-4-6 power frequency magnetic field immunity iec 61000-4-8 voltage dips, short interruptions immunity iec 61000-4-11 fcc part 15 subpart b, class b, ansi c63.4 :2003 * note: for 528vac models to meet the en55022 class b spec an external 0.33uf x capacitor is needed to be installed between ac l and ac n as close as possible to the input of the power supply itself pin out specifications* * note: input pins 1 and 2 can be ?n? and "l" respectively w hen the input voltage is supplied from a single phase. input pins 1 and 2 can be ?l1? and "l2" respectively when the input voltage is supplied from 3 phase line to line voltage 208-4 80vac (208 y/ 120v 3-phase, 240 y/ 120v 3-phase, 400 y/ 230v 3-phase or 480 y/ 277v 3-phase). pin single 1* ac input (n) or (l1) 2* ac input (l) or (l2) 3 -v output 4 +v output
series ame1-az 1watt | ac-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r8.h 3 of 3 north america only dimensions 35.60 (1.40) 15.24 (0.60) 28.00 (1.10) 19.32 (0.76) 6.00 (0.24) dimensions mm (inch) case tolerance 0.50 (0.02) pin diameter 0.05 (0.002) pin pitch tolerance 0.50 (0.02) 0.60 (0.02) ew easuring point 4 2 (0.65) 1 top vi te mperat ure m 3 11.655 (0.46) div: 5.00 (0.20) ? 10.0 ( ? 0.40) ? 0.60 ( ? 0.02) 1 3 top view 4 2 7.60 23.31 (0.92) (0.29) side view ?? ? note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency ce rtifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted dest ructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com.
|
